Plumbing Basics: The First Step for Bathtub Installation
Plumbing Basics: The First Step for Bathtub Installation
Blog Article
On this page in the next paragraph yow will discover more worthwhile content when it comes to How to Install a Bathtub Yourself.
Mounting a bathtub isn't specifically brain surgery, yet it does call for strong plumbing, woodworking, and also often, tiling skills. Changing an old bath tub with a brand-new one is also a moderately challenging job. If the old bathtub is conveniently available, the task can relocate rapidly; if you need to open up a wall surface to eliminate the old bathtub and also position the new bathtub, the job is much harder. In either situation, the task is within a home handyman's abilities, although you will certainly require an assistant to leave the old bathtub and also set in the new one. Make certain you have actually qualified on your own for the job as well as are comfortable trying it. As opposed to employing a professional to take over a halfway-completed task, it is far better to consider using one prior to you begin. Possibilities are you may require an expert plumber to make tube connections.
This article will certainly aid you set up a new bath tub in your restroom if you have currently gotten a new bathtub as well as do not need to transform the arrangement of your previous water pipes.
Your tools as well as product list should comprise the following:
Preparing for the Setup
First of all, the sustaining framework provided with the bathroom ought to be fitted (if called for) according to the maker's directions. Next off, fit the taps or mixer to the tub. When fitting the tap block, it is essential to ensure that if the faucet comes with a plastic washing machine, it is fitted in between the bathroom and also the taps. On a plastic bathroom, it is also practical to fit a sustaining plate under the faucets system to prevent stress on the bath tub.
Fit the versatile faucet adapters to the bottom of the two taps utilizing 2 nuts as well as olives (sometimes supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the outlet via the hole in the bath. Utilize the nut provided by the manufacturer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the versatile overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bathroom. Make sure you use all of the supplied washing machines.
Link the catch to the bottom of the waste outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Link the bottom of the overflow tube in a similar manner.The bath ought to currently prepare to be fitted in its final placement.
Removing Old Taps
If you need to replace old taps with brand-new ones as a part of your installation, then the first thing you must do is separate the supply of water. After doing so, activate the faucets to drain pipes any type of water continuing to be in the system. The procedure of eliminating the existing faucets can be quite problematic due to the restricted accessibility that is usually the case.
Make use of a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that links the supply pipes to the faucets. Have a towel all set for the staying water that will certainly originate from the pipelines. When the supply pipes have been removed, utilize the exact same tool to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to stop the solitary taps from transforming during this procedure. When the faucets have actually been gotten rid of, the holes in the bath/basin will need to be cleansed of any type of old securing substance.
Before carrying on to fit the new taps, compare the pipe connections on the old taps to the brand-new taps. If the old taps are longer than the new taps, then a shank adapter is required for the brand-new faucets to fit.
Setting up the Bathtub
Making use of both wooden boards under its feet, put the tub in the called for position. The wood boards are practical in equally spreading out the weight of the bathtub over the area of the boards instead of focusing all the weight onto 4 little points.
The next goal is to make certain that the tub is leveled all round. This can be achieved by examining the level as well as changing the feet on the bath tub until the level checks out level.
To mount taps, fit all-time low of the outermost flexible tap connector to the proper supply pipeline by making a compression sign up with; after that do the exact same for the various other tap.
Switch on the water system and also check all joints and new pipework for leaks and also tighten them if needed. Fill up the bath tub as well as additionally examine the overflow outlet and the typical electrical outlet for leaks.
Finally, fix the bathroom paneling as explained in the producer's user's manual. Tiling and also securing around the bath tub must wait up until the bath tub has been used a minimum of when as this will certainly resolve it into its last setting.
Suitable New Touches
If the tails of the new faucets are plastic, after that you will certainly need a plastic connector to avoid damages to the thread. One end of the connector fits on the plastic tail of the faucet and also the other end gives a link to the existing supply pipelines.
If you require to fit a monobloc, then you will call for lowering couplers, which connects the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
Next off, place the faucet in the mounting hole in the bath/basin guaranteeing that the washers remain in place in between the faucet as well as the sink. Protect the faucet in position with the maker supplied backnut. Once the tap is securely in place, the supply pipes can be attached to the tails of the taps. The taps can either be linked by utilizing corrugated copper piping or with regular faucet adapters. The former type needs to be attached to the tap finishes first, tightening only by hand. The supply pipelines can later on be connected to the various other end. Tighten up both ends with a spanner after both ends have actually been attached.
Tiling Around the Bath tub
In the area where the bathroom satisfies the ceramic tile, it is needed to seal the accompanies a silicone rubber caulking. This is very important as the installation can move sufficient to break a rigid seal, triggering the water to penetrate the wall between the bathroom and also the tiling, leading to issues with moisture as well as feasible leakages to the ceiling below.
You can choose from a selection of coloured sealants to blend in your components and fittings. They are offered in tubes and also cartridges, and can sealing voids up to a width of 3mm (1/8 inch). If you have a bigger void to fill, you can fill it with twists of drenched newspaper or soft rope. Bear in mind to constantly load the bathtub with water before sealing, to permit the movement experienced when the tub is in use. The sealer can crack rather very early if you do not think about this activity prior to sealing.
Alternatively, ceramic coving or quadrant floor tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are also easily available on the market. It is recommended to fit the ceramic tiles utilizing water-resistant or water resistant adhesive as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I discovered that blog posting on Tools You Need to Install a New Bathtub when surfing around the internet. I beg you take the time to promote this blog if you enjoyed reading it. We treasure reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Schedule Your Service Report this page